Is it time to replace the battery of your Spot device? Read the guide below on how to order and replace the battery of your Spot device.
Not sure if your battery needs changing? See this article about Spot battery life management
How do I order a new battery?
Contact your key account manager or customer success manager to place an order. The relevant part number for Spot is 9862.013601.
If you are unsure who to contact, reach out to our Customer Support team, and they can point you in the right direction.
Safety Statement
 | Intended use The battery (Part number 9862.013601) is intended for professional, instructed battery replacement in Spot 2 and Spot S300. Misuse Do not install other battery types than 9862.013601 in Spot 2 and Spot S300. Do not solder a battery to the product. |
 | Risk of fire/explosion The battery is packed at the factory for safe transportation. Only unpack the battery before the replacement. Do not heat, puncture, or crush the battery due to risk of fire/explosion. |
 | Installation
|
 | Disposal Dispose of the replaced battery only through a local collection scheme. |
Technical Specifications
Description | Technical Specification |
Part Number | 9862.013601 |
Type | 1S2P LSP17500-20F1 Li-SOCl2 |
Li-metal content | Maximum 2 g |
Battery weight | 52.0 g |
Storage temperature (recommended) | +30 degrees Celsius maximum |
Transport | UN3090; UN3091 |
Spot Battery Replacement Steps
The process for replacing your Spot batteries is slightly different for Spot 2 devices and Spot S300 devices.
After replacing the battery of either Spot 2 or Spot S300, make sure to reset the battery counters in Trackunit Manager
Battery replacement of Spot S300:
The Spot S300 housing is made of two parts: the sleeve (the outer shell with the laser etchings of serial number and 2D code) and the plug (the end without any laser etchings to which the internal assembly is attached). The sleeve slides on to the other piece and locks on with two tabs.
To replace the battery you pop the two clips loose and separate the sleeve from the plug. No tools are required, although a flat-head screwdriver makes releasing the clips easier.
[Photo/render 1: S300 showing the two clips on the sleeve and where to press/lever them. Photo/render 2: sleeve separated from the plug with the battery pack visible and its orientation clearly shown]
Remove the device: Detach the Spot S300 from its mounting location by unfastening the screws or lifting it off the magnetic mount (if applicable).
Release the clips: Locate the two clips on the sleeve, one on each side. Pop each clip loose from the plug with your fingers, or use a flat-head screwdriver to gently lever it free.
Separate the sleeve from the plug: With both clips released, slide the sleeve off the plug. Some resistance from the sealing gasket is normal.
Disconnect the old battery: Remove the battery pack and disconnect it from the connector.
Dispose of the old battery: Follow local, state, or provincial laws and regulations for battery disposal.
Check the seal: Make sure the sealing gasket is clean, undamaged, and seated in its groove. A damaged or misplaced gasket will compromise the IP rating.
Connect the new battery: Connect the new Trackunit battery pack (P/N 9862.013601) to the connector.
Reassemble: Slide the sleeve back over the plug until both clips snap into place. Check that both clips are fully engaged and the sleeve sits flush all the way round — this is what maintains the IP rating.
Battery replacement of Spot 2:
Remove the device: Detach the Spot from its mounting location by unfastening or removing it from the magnetic mounting bracket (if applicable).
Unscrew the back panel: Use the TX10 screwdriver to remove the four M4 screws from the back panel.
Open the housing: Separate the front and back panels. Some force might be required — be careful not to damage any components.
Disconnect the old battery: Carefully remove the old battery and disconnect it from the JST connector (location displayed in the figure below) by gently pulling up on the wires.
Dispose of the old battery: Follow local, state, or provincial laws and regulations for battery disposal.
Install the new battery: Install the new Trackunit battery pack (P/N: 9862.013601) by hand, inserting the JST connector on the new battery pack in the JST slot on the Spot within the enclosure.
Check LED confirmation: The LEDs flash green and red for approximately two seconds to confirm the battery has been installed correctly.
Reassemble the device: Align the back panel carefully, covering the battery, making sure no wires are pinched or pierced.
Secure the screws: Insert four M4 screws into the screw holes on the back panel and tighten them using the TX10 (0.6 Nm) screwdriver. Avoid over-tightening.
💡 Tip: If you’re using the Spot 2 Magnetic Bracket, download the installation guide and safety statement here
Resetting battery counters after replacement
After replacing the battery, be sure to reset the battery counter in Trackunit Manager to update the device’s estimated lifespan.
Log in to Trackunit Manager.
Go to the Assets page at the top of the navigation bar on the left.
Select the asset with the Spot battery that you replaced.
In Asset home, click on the Telematics tab.
In the Battery Status section, click on Reset counters to reset the values.
Your Spot battery is now successfully replaced and reset. The battery estimate will recalibrate to the new battery over the following weeks as the device reports.
If you have any issues or questions during the replacement process, don't hesitate to reach out to our Customer Support team via our Messenger
More questions regarding your Spot?
💡 Tip:
Need more help?
Click on the Messenger icon in the lower left corner to get in touch with Customer Support.